A single component primer formulated to improve topcoat adhesion on bare metal, galvanized steel, stainless steel, aluminum and other substrates.
• Provides maximum adhesion and corrosion
resistance on all types of bare metal
• Can be used on steel, aluminum and
galvanized steel
• 1-2 medium wet coats
DRY TIMES:
• Allow 30 minutes @ 70°F (21°C) air
dry before priming. Total milage should
be 0.5 to 0.75 mil.
SANDING:
• Can be primed without sanding. If Primer is not primed within 16 hours it should be sanded with 180-240 grit sandpaper
An acid-based, etching primer designed to optimize adhesion to bare metal substrates and provide a corrosion resistant barrier between substrate and coatings.
• 2 Part coating
• Designed to give maximum adhesion and
corrosion resistance on, Lacquer Primer Surfacer,
Epoxy Primer Sealer, 2K Urethane Sealer
• 1-2 Medium wet coats
DRY TIMES:
• Allow 30 minutes @ 70°F (21°C) air
dry before priming
SANDING:
• Can be primed without sanding. If Primer is not primed within 16 hours it should be sanded with 180-240 grit sandpaper
A premium quality acrylic lacquer primer for use in automotive applications. It is formulated with the highest quality resins
• Very fast dry time; sand in approximately 30
minutes
• Excellent adhesion to cured finishes, body filler and sanded fiberglass
• Superior filling and sanding properties
• 2-3 Full wet coats
SANDING
• Allow to thoroughly dry before sanding.
Finish sand as follows:
• Sealer | 320-400 grit
• Single-stage system | 320-400 grit
• Basecoat | 400-500 grit
A fast-dry epoxy with excellent corrosion resistance and adhesion to a variety of properly prepared metals and some automotive plastics.
• Can be directly topcoated, wet-on-wet, with any topcoat system
• Fast dry, fast curing epoxy that has excellent
corrosion resistance and adhesion
• Can be used as a primer surfacer or a sealer
• Tintable
• 1-2 Full wet coats
A two-component primer surfacer that has excellent adhesion to cold-rolled steel, aluminum, galvanized panels, galvanneal, body filler, fiberglass, SMC and OEM finishes.
• Has excellent anti-corrosion properties and sands
easily without loading the sandpaper.
• Eliminates the need for pre-treatment primer
• Easily sprays and levels with little overspray
• 2-3 Full wet coats
DRY TIMES:
AIR DRY
• Dry to Sand 90 minutes
• Flash Between Coats 10-15 minutes
EXPRESS DRY
• Flash between coats 10-15 minutes
• Flash before force dry (Purge Time)
10 minutes
• Cycle Time 15-20 minutes@140F
A two-component primer surfacer that has excellent adhesion to cold-rolled steel, aluminum, galvanized panels, galvanneal, body filler, fiberglass, SMC and OEM finishes.
• Has excellent anti-corrosion properties and sands
easily without loading the sandpaper.
• Eliminates the need for pre-treatment primer
• Easily sprays and levels with little overspray
• 2-3 Full wet coats
DRY TIMES:
• Air Dry: Dry to Sand 1-1/2 to 2 hours
• Express Dry: Cycle Time IR 15-20 minutes
A dual-purpose, high-build specialty coating
designed for priming and surfacing of metal and plastic parts. This primer helps prevent rust and seals out moisture while providing a base for topcoating.
• Must be topcoated with another primer before topcoating with polyester-based coatings.
• 2 coats at a distance of approx. 10 inches from the surface.
• 20oz. Aerosol can
INSTRUCTIONS
• Shake the aerosol can for at least 2 minutes before use.
• For best results, ensure the surface is thoroughly cleaned, degreased, dried and dust free. Abrade primed surfaces wet or dry with P180 - P220 grit sandpaper,
degrease and dry.
READY TO SPRAY | 4.2 VOC
SUBSTRATES
• Bare steel
• Aluminum
• Galvanized and zinc coated steels
• Polyester bodyfillers and GRP
• Fully cured paint
FLASH OFF
• 3-5 minute flash between coats
DRY TIMES
• Drying Times: 3-5 mins between coats @ 68°F
PRIMER: DI-741
PART NUMBER INFORMATION:
HIGH BUILD PRIMER
READY TO SPRAY | 4.2 VOC
FEATURES:
A dual-purpose, high-build specialty coating
designed for priming and surfacing of metal and plastic parts. This primer helps prevent rust and seals out moisture while providing a base for topcoating.
• Excellent flexibility and adhesion so it can be
applied on both flexible and rigid parts.
• Dries fast, has excellent build and is easy to sand.
• Paintable in 20 minutes.
• 20oz. Aerosol can
TECHNICAL NOTES:
• Compatible with All basecoat systems
• Designed to powerfully adhere to both plastic and metal
SUBSTRATES:
• Direct to Metal
• SMC
• Lighty abraded E-Coat
• Fiberglass
• OEM paint surfaces